|
Woodmont Doors
Profiles page, along with wood finish colors, and hinge boring information
|
Here's the simplicity of the profiles:
Series 200 raised panel doors require you to select a) frame profile, b) panel profile, c) edge profile.
Series 400
plywood panel doors require your selection of a) frame profile, b) edge profile. You can also select between the default smooth plywood panel or the B panel which is a beaded plywood panel.
Series 100
mitered corner raised panel doors require you to select a) panel profile, and in some cases, maybe an edge profile.
The diagrams below are shown on each of those WOOD door series pages where they apply.
|
Frame profiles
Panel profiles
 Edge profiles
For series 300 and 400 doors, these have a plywood panel. Your plywood panel options are smooth or beaded. The beaded
plywood panel is not the same panel as the beaded raised panel choice. The beaded raised panel choice technically is not a raised panel, but it is thicker and solid wood.
Above diagram shows the 4 basic series and how the panel choice fits into the frame choice, and then the edge profile is the very
perimeter of the entire door. Not all options are available on all doors. The above diagram is for reference for all door series. 
An illustration of a five-piece door and how profiles relate to each other.
|
Finish options: All doors, plywood, veneer, and moldings are available in Red Oak, Maple, Cherry or Hickory woods. Paint grade available too for doors and drawer fronts.
Doors can be ordered unfinished, or you can request finishing from the choices below.
If you would like a glazed finish, glaze colors are chocolate, bronze, mocha, and almond.
Paint grade doors come unfinished only, they are fine sanded and ready for you to paint. PLEASE NOTE: Finish choices are restricted by wood species.
Autumn Oak, Nutmet Oak, Harvest Oak, and Charcoal Oak are Oak wood finish options.
Harvest Maple, Natural Maple, Toffe Maple, Ginger Maple, Champagne Maple, Cider Maple, Cordovan Maple, and Espresso Maple are Maple
wood finishes.
Cider Cherry, Cordovan Cherry, Ginger Cherry, and also Natural Cherry are Cherry wood finishes.
Cider Hickory, Natural Hickory, and Autumn Hickory are Hickory wood finishes.
|
Hinge boring options: If you would like your doors bored for concealed 35mm cup hinges,
please select boring option #1 or option #2 as shown below.
**For arch top designs state BL (bore left); BR (bore right); BP (bore as pairs).
Hinges for 1/2" overlay on a face frame edge mount are available from Woodmont Doors.
Hinge boring is $2.10 per door, conceal hinges WD-900CD are $5 per pair.
If you require special placement of hinge holes other than the standard 3-1/8" on center for doors over 9" tall, the distance from the top or
bottom of the door can be altered. The edge distance of 3/32" remains a constant, that is not alterable. Special boring is done at $6.00 per door. Standard boring is just $2.10 per door.
|
Various hinge options that we can offer you
|
These are the WD-900CD
hinges that can be shipped from Woodmont with your door order. This is the only hinge we can get from them. Concealed face frame mount, 1/2" overlay, mounts to edge of face frame, 35mm bore, with dowels attached. This goes with Woodmont's B1 boring pattern of 3 holes.
Dowels are removeable if you wish to convert the hinge to a screw-on version. Thus the B2 boring method.
WD-900CD @ $5.00 per pair
|
These are the Blum Compact 38N hinges. These two hinges were known as the 900C and 900CD from Quality Doors. Extremely similar to the hinge just above, but these are the Blum brand. Available
as a screw on version, to go with the B2 boring method, or as a knock-in (press-in) version, to go with the 3-hole boring pattern B1 shown above. 6-way adjustable. Looking at the picture below, you see two
screws on the plate side of the hinge. One screw will adjust the hinge left to right, thus the tilt of your door. The other screw adjusts the hinge in and out, thus the tightness to your cabinet. Then the
oval slotted hole between them gives you the height adjustment to tweak your hinge up and door to help align tops of doors to each other.
This hinge is for a 1/2" overlay which is by far the most common application in "face frame" cabinetry.
When we supply these hinges, we will include the necessary mounting screws too.
BLU-38N355C.08 @ $2.50 each - Screw-on, self-closing (no dowels, old 900C)
BLU-38N358C.08 @ $2.50 each
- Press-in, self-closing (with dowels, old 900CD)
|
Blum Euro-box hinges for frameless applications.
When you do not have face frame cabinetry and would like concealed hinges, these are the kind you want to use. Shown below are the overlay
(by far the most common), and the inset vesion of the Blum Cliptop 107 hinge. This means your cabinet door will open 107 degrees, which is quite normal. Blum also has hinges that open doors 120 degrees and
170 degrees. We are just showing the 107 degree because that is all that is needed 99% of the time. If ordering in conjunction with Woodmont Doors, select boring method B2. These hinges are available in
press-in versions, but it is easier to offer them as screw-on. The reason being, if you are replacing hinges and keeping the same doors, do you know if your doors have the Blum, Grass, Mepla, KV, Ferrari,
Salice, etc. boring pattern? Not all are alike, and the dowels may not line up. With a screw on hinge, you don't have to worry about dowel placement.
BLU-75T1550 @ $2.96 each - Cliptop 107 screw-on FULL overlay hinge, self-closing
BLU-75T1750 @ $3.04 each - Cliptop 107 screw-on INSET hinge, self-closing
BLU-175H7100 @ $1.37 each - Clip mounting plate, 0mm
|
Blum Compact 33 face frame mount hinges.
For more adjustability in your overlay.
Blum Compact 33 hinges are 110 degree opening self-closing hinges, that when combined with the mounting
plate of your choice will allow for face frame overlays from 1/4" up to 1-5/8". A two-piece hinge and plate combination give you great flexibility. Plates we show below are edge mounted to the face frame.
The second pitcure shows how the hinge arm just slips into the mounting plate, then the set screw will tighten down.
Hinge can come as screw-on or press-in version. Attaches with #6x5/8" wood screws.
BLU-33.360 @ $2.77 each - screw-on hinge
BLU-33.363 @ $2.77 each - press-in hinge with dowels (not shown above)
BLU-130.1100.23 @ $1.32 each
- 1/2" overlay mounting plate (most common size used)
All other sizes of mounting plates are also $1.32 each. The sizes are:
BLU-130.1100.24 = 1/4" overlay
BLU-130.1100.26 = 5/8" overlay
BLU-130.1100.22 = 3/4" overlay
BLU-130-1110.02 = 1" overlay
BLU-130.1120.02 = 1-1/8" overlay
BLU-130.1130.02 = 1-1/4" overlay
BLU-130.1140.02 = 1-3/8" overlay
BLU-130.1150.02 = 1-1/2" overlay
BLU-130.1160 = 1-5/8" overlay
|
Last but not least in our chosen selection of "concealed" cabinet hinges:
The Salice F series hinges.
This is the hinge we have offered for years with the Accuride Flipper Door systems.
It is a 40mm bore, thus you would have to bore the hole yourself, Woodmont only bores for 35mm hinges. This is considered a "thick door" hinge, but you do not have to use it on just thick doors. What a thick
door hinge does is just swing the door out farther away from the edge of your cabinet. This is why it is a good hinge for the pocketing door systems. It is a great hinge to use, because it is incredibly
strong. The 40mm cup and larger hinge arm make it a very tough hinge. We offer it in self-closing and free-swinging versions.
SAL-A00A7A @ $4.42 each
- FULL overlay, self-closing
SAL-A00A7G @ $4.52 each - HALF overlay, self-closing
SAL-A00A7P @ $4.68 each - INSET, self-closing
SAL-A00A5A @ $4.35 each - FULL overlay, free-swinging
SAL-A00A5G @ $4.48 each - HALF overlay, free-swinging
SAL-A00A5P @ $4.54 each
- INSET, free-swinging
SAL-AAR3E0 @ $1.23 each - mounting plate, 0mm
|
|
How to calculate square footage:
Multiple your width in inches by your height in inches, divide by 144, round off to the second decimal place.
Example: your door is 15-7/8" wide x 27-9/16" tall. (15.875 x 27.5625)/144 = 3.04 sq. ft.
If you are uncertain how to determine the decimal equivalent of a fraction,
just divide the top number by the bottom number.
Examples: 7/8 is 7 divided by 8 = .875. Or 13/16 is 13 divided by 16 = .8125. Square foot calculations for frame only or mullion doors is different and described on the mullion door page. Please remember, we will quote out your request for you if you would like to submit your information on-line.
|
PROCEED TO:
|
PROCEED TO:
|
|
